IZUMI Tv Software Update

05/08/2023
0 12

IZUMI TL37F210B LED TV FLASH DUMP
Download Here

IZUMI TL37F210B LED TV

IZUMI TL37F210B LED TV Software file is shared for repairing purpose. If the IZUMI TL37F210B LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the IZUMI TL37F210B LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and IZUMI TL37F210B LED TV is still dead then check the primary power circuit if found ok then test the sIZUMIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIZUMIdary voltage of the main board of the IZUMI TL37F210B LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in IZUMI TL37F210B LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IZUMI TL37F210B LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications IZUMI TL37F210B LED TV:
- Make/Brand: IZUMI
- Main Board/Chassis: 090-A6M480-00
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: IZUMI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

IZUMI TL37F210B LED TV dump file is shared below for repairing the firmware problem. IZUMI TL37F210B LED TV has the main board 090-A6M480-00 installed in it so the SPI Flash file backup saved from working board 090-A6M480-00. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. 090-A6M480-00 dump file is shared below for the IZUMI TL37F210B LED TV repairing.

IZUMI TL37F210B LED TV Software download free.

How to Download Free Software for IZUMI TL37F210B LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
05/08/2023
0 11

IZUMI TLE32H410 LED TV FLASH DUMP
Download Here

IZUMI TLE32H410 LED TV

IZUMI TLE32H410 LED TV Software file is shared for repairing purpose. If the IZUMI TLE32H410 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the IZUMI TLE32H410 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and IZUMI TLE32H410 LED TV is still dead then check the primary power circuit if found ok then test the sIZUMIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIZUMIdary voltage of the main board of the IZUMI TLE32H410 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in IZUMI TLE32H410 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IZUMI TLE32H410 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications IZUMI TLE32H410 LED TV:
- Make/Brand: IZUMI
- Main Board/Chassis: HK-T.MST182V03
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: IZUMI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

IZUMI TLE32H410 LED TV dump file is shared below for repairing the firmware problem. IZUMI TLE32H410 LED TV has the main board HK-T.MST182V03 installed in it so the SPI Flash file backup saved from working board HK-T.MST182V03. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK-T.MST182V03 dump file is shared below for the IZUMI TLE32H410 LED TV repairing.

IZUMI TLE32H410 LED TV Software download free.

How to Download Free Software for IZUMI TLE32H410 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
05/08/2023
0 13

IZUMI TLE24F150G LED TV FLASH DUMP
Download Here

IZUMI TLE24F150G LED TV

IZUMI TLE24F150G LED TV Software file is shared for repairing purpose. If the IZUMI TLE24F150G LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the IZUMI TLE24F150G LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and IZUMI TLE24F150G LED TV is still dead then check the primary power circuit if found ok then test the sIZUMIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIZUMIdary voltage of the main board of the IZUMI TLE24F150G LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in IZUMI TLE24F150G LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IZUMI TLE24F150G LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications IZUMI TLE24F150G LED TV:
- Make/Brand: IZUMI
- Main Board/Chassis: HK-T.MST182V01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: IZUMI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

IZUMI TLE24F150G LED TV dump file is shared below for repairing the firmware problem. IZUMI TLE24F150G LED TV has the main board HK-T.MST182V01 installed in it so the SPI Flash file backup saved from working board HK-T.MST182V01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK-T.MST182V01 dump file is shared below for the IZUMI TLE24F150G LED TV repairing.

IZUMI TLE24F150G LED TV Software download free.

How to Download Free Software for IZUMI TLE24F150G LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
05/08/2023
0 13

IZUMI TLE32H150G LED TV FLASH DUMP
Download Here

IZUMI TLE32H150G LED TV

IZUMI TLE32H150G LED TV Software file is shared for repairing purpose. If the IZUMI TLE32H150G LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the IZUMI TLE32H150G LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and IZUMI TLE32H150G LED TV is still dead then check the primary power circuit if found ok then test the sIZUMIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIZUMIdary voltage of the main board of the IZUMI TLE32H150G LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in IZUMI TLE32H150G LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IZUMI TLE32H150G LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications IZUMI TLE32H150G LED TV:
- Make/Brand: IZUMI
- Main Board/Chassis: HK-T.MST182V03
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: IZUMI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

IZUMI TLE32H150G LED TV dump file is shared below for repairing the firmware problem. IZUMI TLE32H150G LED TV has the main board HK-T.MST182V03 installed in it so the SPI Flash file backup saved from working board HK-T.MST182V03. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK-T.MST182V03 dump file is shared below for the IZUMI TLE32H150G LED TV repairing.

IZUMI TLE32H150G LED TV Software download free.

How to Download Free Software for IZUMI TLE32H150G LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
05/08/2023
0 1,675

IZUMI TLE24F410M LED TV FLASH DUMP
Download Here

IZUMI TLE24F410M LED TV

IZUMI TLE24F410M LED TV Software file is shared for repairing purpose. If the IZUMI TLE24F410M LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the IZUMI TLE24F410M LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and IZUMI TLE24F410M LED TV is still dead then check the primary power circuit if found ok then test the sIZUMIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIZUMIdary voltage of the main board of the IZUMI TLE24F410M LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in IZUMI TLE24F410M LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IZUMI TLE24F410M LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications IZUMI TLE24F410M LED TV:
- Make/Brand: IZUMI
- Main Board/Chassis: HK-T.MST182V01
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: IZUMI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

IZUMI TLE24F410M LED TV dump file is shared below for repairing the firmware problem. IZUMI TLE24F410M LED TV has the main board HK-T.MST182V01 installed in it so the SPI Flash file backup saved from working board HK-T.MST182V01. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. HK-T.MST182V01 dump file is shared below for the IZUMI TLE24F410M LED TV repairing.

IZUMI TLE24F410M LED TV Software download free.

How to Download Free Software for IZUMI TLE24F410M LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
05/08/2023
0 14

IZUMI TLE32H410M LED TV FLASH DUMP
Download Here

IZUMI TLE32H410M LED TV

IZUMI TLE32H410M LED TV Software file is shared for repairing purpose. If the IZUMI TLE32H410M LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the IZUMI TLE32H410M LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and IZUMI TLE32H410M LED TV is still dead then check the primary power circuit if found ok then test the sIZUMIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIZUMIdary voltage of the main board of the IZUMI TLE32H410M LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in IZUMI TLE32H410M LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IZUMI TLE32H410M LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications IZUMI TLE32H410M LED TV:
- Make/Brand: IZUMI
- Main Board/Chassis: MST6M181VS-V3.0
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: IZUMI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

IZUMI TLE32H410M LED TV dump file is shared below for repairing the firmware problem. IZUMI TLE32H410M LED TV has the main board MST6M181VS-V3.0 installed in it so the SPI Flash file backup saved from working board MST6M181VS-V3.0. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MST6M181VS-V3.0 dump file is shared below for the IZUMI TLE32H410M LED TV repairing.

IZUMI TLE32H410M LED TV Software download free.

How to Download Free Software for IZUMI TLE32H410M LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
05/08/2023
0 68

IZUMI TLE32H400W LED TV FLASH DUMP
Download Here

IZUMI TLE32H400W LED TV

IZUMI TLE32H400W LED TV Software file is shared for repairing purpose. If the IZUMI TLE32H400W LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the IZUMI TLE32H400W LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and IZUMI TLE32H400W LED TV is still dead then check the primary power circuit if found ok then test the sIZUMIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIZUMIdary voltage of the main board of the IZUMI TLE32H400W LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in IZUMI TLE32H400W LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IZUMI TLE32H400W LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications IZUMI TLE32H400W LED TV:
- Make/Brand: IZUMI
- Main Board/Chassis: MST6M181VS-V3.0
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: IZUMI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

IZUMI TLE32H400W LED TV dump file is shared below for repairing the firmware problem. IZUMI TLE32H400W LED TV has the main board MST6M181VS-V3.0 installed in it so the SPI Flash file backup saved from working board MST6M181VS-V3.0. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MST6M181VS-V3.0 dump file is shared below for the IZUMI TLE32H400W LED TV repairing.

IZUMI TLE32H400W LED TV Software download free.

How to Download Free Software for IZUMI TLE32H400W LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
05/08/2023
0 76

IZUMI TLE32H400B LED TV FLASH DUMP
Download Here

IZUMI TLE32H400B LED TV

IZUMI TLE32H400B LED TV Software file is shared for repairing purpose. If the IZUMI TLE32H400B LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the IZUMI TLE32H400B LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and IZUMI TLE32H400B LED TV is still dead then check the primary power circuit if found ok then test the sIZUMIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIZUMIdary voltage of the main board of the IZUMI TLE32H400B LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in IZUMI TLE32H400B LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IZUMI TLE32H400B LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications IZUMI TLE32H400B LED TV:
- Make/Brand: IZUMI
- Main Board/Chassis: MST6M181VS-V3.0
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: IZUMI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

IZUMI TLE32H400B LED TV dump file is shared below for repairing the firmware problem. IZUMI TLE32H400B LED TV has the main board MST6M181VS-V3.0 installed in it so the SPI Flash file backup saved from working board MST6M181VS-V3.0. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MST6M181VS-V3.0 dump file is shared below for the IZUMI TLE32H400B LED TV repairing.

IZUMI TLE32H400B LED TV Software download free.

How to Download Free Software for IZUMI TLE32H400B LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
05/08/2023
0 15

IZUMI TL32H601B LED TV FLASH DUMP
Download Here

IZUMI TL32H601B LED TV

IZUMI TL32H601B LED TV Software file is shared for repairing purpose. If the IZUMI TL32H601B LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the IZUMI TL32H601B LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and IZUMI TL32H601B LED TV is still dead then check the primary power circuit if found ok then test the sIZUMIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIZUMIdary voltage of the main board of the IZUMI TL32H601B LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in IZUMI TL32H601B LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IZUMI TL32H601B LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications IZUMI TL32H601B LED TV:
- Make/Brand: IZUMI
- Main Board/Chassis: MST6M181VS-V4.0
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: IZUMI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

IZUMI TL32H601B LED TV dump file is shared below for repairing the firmware problem. IZUMI TL32H601B LED TV has the main board MST6M181VS-V4.0 installed in it so the SPI Flash file backup saved from working board MST6M181VS-V4.0. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MST6M181VS-V4.0 dump file is shared below for the IZUMI TL32H601B LED TV repairing.

IZUMI TL32H601B LED TV Software download free.

How to Download Free Software for IZUMI TL32H601B LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
05/08/2023
0 12

IZUMI TLE26H400B LED TV FLASH DUMP
Download Here

IZUMI TLE26H400B LED TV

IZUMI TLE26H400B LED TV Software file is shared for repairing purpose. If the IZUMI TLE26H400B LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the IZUMI TLE26H400B LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and IZUMI TLE26H400B LED TV is still dead then check the primary power circuit if found ok then test the sIZUMIdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sIZUMIdary voltage of the main board of the IZUMI TLE26H400B LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in IZUMI TLE26H400B LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given IZUMI TLE26H400B LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications IZUMI TLE26H400B LED TV:
- Make/Brand: IZUMI
- Main Board/Chassis: MST6M181VS-V3.0
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: IZUMI
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

IZUMI TLE26H400B LED TV dump file is shared below for repairing the firmware problem. IZUMI TLE26H400B LED TV has the main board MST6M181VS-V3.0 installed in it so the SPI Flash file backup saved from working board MST6M181VS-V3.0. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. MST6M181VS-V3.0 dump file is shared below for the IZUMI TLE26H400B LED TV repairing.

IZUMI TLE26H400B LED TV Software download free.

How to Download Free Software for IZUMI TLE26H400B LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done