ERGO Download Center

19/07/2023
0 37

ERGO LE40CT5000AK LED TV FLASH DUMP
Download Here

ERGO LE40CT5000AK LED TV

ERGO LE40CT5000AK LED TV Software file is shared for repairing purpose. If the ERGO LE40CT5000AK LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ERGO LE40CT5000AK LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ERGO LE40CT5000AK LED TV is still dead then check the primary power circuit if found ok then test the sERGOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sERGOdary voltage of the main board of the ERGO LE40CT5000AK LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ERGO LE40CT5000AK LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ERGO LE40CT5000AK LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ERGO LE40CT5000AK LED TV:
- Make/Brand: ERGO
- Main Board/Chassis: TP.MS3663S.PB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ERGO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ERGO LE40CT5000AK LED TV dump file is shared below for repairing the firmware problem. ERGO LE40CT5000AK LED TV has the main board TP.MS3663S.PB801 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PB801 dump file is shared below for the ERGO LE40CT5000AK LED TV repairing.

ERGO LE40CT5000AK LED TV Software download free.

How to Download Free Software for ERGO LE40CT5000AK LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
19/07/2023
0 19

ERGO 43DFT7000 LED TV FLASH DUMP
Download Here

ERGO 43DFT7000 LED TV

ERGO 43DFT7000 LED TV Software file is shared for repairing purpose. If the ERGO 43DFT7000 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ERGO 43DFT7000 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ERGO 43DFT7000 LED TV is still dead then check the primary power circuit if found ok then test the sERGOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sERGOdary voltage of the main board of the ERGO 43DFT7000 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ERGO 43DFT7000 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ERGO 43DFT7000 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ERGO 43DFT7000 LED TV:
- Make/Brand: ERGO
- Main Board/Chassis: TP.MS3663S.PB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ERGO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ERGO 43DFT7000 LED TV dump file is shared below for repairing the firmware problem. ERGO 43DFT7000 LED TV has the main board TP.MS3663S.PB801 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PB801 dump file is shared below for the ERGO 43DFT7000 LED TV repairing.

ERGO 43DFT7000 LED TV Software download free.

How to Download Free Software for ERGO 43DFT7000 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
19/07/2023
0 12

ERGO LE43CT5000AK LED TV FLASH DUMP
Download Here

ERGO LE43CT5000AK LED TV

ERGO LE43CT5000AK LED TV Software file is shared for repairing purpose. If the ERGO LE43CT5000AK LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ERGO LE43CT5000AK LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ERGO LE43CT5000AK LED TV is still dead then check the primary power circuit if found ok then test the sERGOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sERGOdary voltage of the main board of the ERGO LE43CT5000AK LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ERGO LE43CT5000AK LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ERGO LE43CT5000AK LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ERGO LE43CT5000AK LED TV:
- Make/Brand: ERGO
- Main Board/Chassis: TP.MS3663S.PB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ERGO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ERGO LE43CT5000AK LED TV dump file is shared below for repairing the firmware problem. ERGO LE43CT5000AK LED TV has the main board TP.MS3663S.PB801 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PB801 dump file is shared below for the ERGO LE43CT5000AK LED TV repairing.

ERGO LE43CT5000AK LED TV Software download free.

How to Download Free Software for ERGO LE43CT5000AK LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
19/07/2023
0 27

ERGO LE32CT5020JP LED TV FLASH DUMP
Download Here

ERGO LE32CT5020JP LED TV

ERGO LE32CT5020JP LED TV Software file is shared for repairing purpose. If the ERGO LE32CT5020JP LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ERGO LE32CT5020JP LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ERGO LE32CT5020JP LED TV is still dead then check the primary power circuit if found ok then test the sERGOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sERGOdary voltage of the main board of the ERGO LE32CT5020JP LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ERGO LE32CT5020JP LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ERGO LE32CT5020JP LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ERGO LE32CT5020JP LED TV:
- Make/Brand: ERGO
- Main Board/Chassis: TP.MS3663S.PB818
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ERGO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ERGO LE32CT5020JP LED TV dump file is shared below for repairing the firmware problem. ERGO LE32CT5020JP LED TV has the main board TP.MS3663S.PB818 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PB818. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PB818 dump file is shared below for the ERGO LE32CT5020JP LED TV repairing.

ERGO LE32CT5020JP LED TV Software download free.

How to Download Free Software for ERGO LE32CT5020JP LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
19/07/2023
0 18

ERGO LE24CT5000K LED TV FLASH DUMP
Download Here

ERGO LE24CT5000K LED TV

ERGO LE24CT5000K LED TV Software file is shared for repairing purpose. If the ERGO LE24CT5000K LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ERGO LE24CT5000K LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ERGO LE24CT5000K LED TV is still dead then check the primary power circuit if found ok then test the sERGOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sERGOdary voltage of the main board of the ERGO LE24CT5000K LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ERGO LE24CT5000K LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ERGO LE24CT5000K LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ERGO LE24CT5000K LED TV:
- Make/Brand: ERGO
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ERGO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ERGO LE24CT5000K LED TV dump file is shared below for repairing the firmware problem. ERGO LE24CT5000K LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the ERGO LE24CT5000K LED TV repairing.

ERGO LE24CT5000K LED TV Software download free.

How to Download Free Software for ERGO LE24CT5000K LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
19/07/2023
0 15

ERGO LE21CT5000AK LED TV FLASH DUMP
Download Here

ERGO LE21CT5000AK LED TV

ERGO LE21CT5000AK LED TV Software file is shared for repairing purpose. If the ERGO LE21CT5000AK LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ERGO LE21CT5000AK LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ERGO LE21CT5000AK LED TV is still dead then check the primary power circuit if found ok then test the sERGOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sERGOdary voltage of the main board of the ERGO LE21CT5000AK LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ERGO LE21CT5000AK LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ERGO LE21CT5000AK LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ERGO LE21CT5000AK LED TV:
- Make/Brand: ERGO
- Main Board/Chassis: TP.MS3663S.PA671
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ERGO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ERGO LE21CT5000AK LED TV dump file is shared below for repairing the firmware problem. ERGO LE21CT5000AK LED TV has the main board TP.MS3663S.PA671 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PA671. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PA671 dump file is shared below for the ERGO LE21CT5000AK LED TV repairing.

ERGO LE21CT5000AK LED TV Software download free.

How to Download Free Software for ERGO LE21CT5000AK LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
19/07/2023
0 14

ERGO LE39CT5020JP LED TV FLASH DUMP
Download Here

ERGO LE39CT5020JP LED TV

ERGO LE39CT5020JP LED TV Software file is shared for repairing purpose. If the ERGO LE39CT5020JP LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ERGO LE39CT5020JP LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ERGO LE39CT5020JP LED TV is still dead then check the primary power circuit if found ok then test the sERGOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sERGOdary voltage of the main board of the ERGO LE39CT5020JP LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ERGO LE39CT5020JP LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ERGO LE39CT5020JP LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ERGO LE39CT5020JP LED TV:
- Make/Brand: ERGO
- Main Board/Chassis: TP.MS3663S.PB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ERGO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ERGO LE39CT5020JP LED TV dump file is shared below for repairing the firmware problem. ERGO LE39CT5020JP LED TV has the main board TP.MS3663S.PB801 installed in it so the SPI Flash file backup saved from working board TP.MS3663S.PB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3663S.PB801 dump file is shared below for the ERGO LE39CT5020JP LED TV repairing.

ERGO LE39CT5020JP LED TV Software download free.

How to Download Free Software for ERGO LE39CT5020JP LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/07/2023
0 17

ERGO LE32CT5000AK LED TV FLASH DUMP
Download Here

ERGO LE32CT5000AK LED TV

ERGO LE32CT5000AK LED TV Software file is shared for repairing purpose. If the ERGO LE32CT5000AK LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ERGO LE32CT5000AK LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ERGO LE32CT5000AK LED TV is still dead then check the primary power circuit if found ok then test the sERGOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sERGOdary voltage of the main board of the ERGO LE32CT5000AK LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ERGO LE32CT5000AK LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ERGO LE32CT5000AK LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ERGO LE32CT5000AK LED TV:
- Make/Brand: ERGO
- Main Board/Chassis: TP.MS3463S.PB751
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ERGO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ERGO LE32CT5000AK LED TV dump file is shared below for repairing the firmware problem. ERGO LE32CT5000AK LED TV has the main board TP.MS3463S.PB751 installed in it so the SPI Flash file backup saved from working board TP.MS3463S.PB751. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3463S.PB751 dump file is shared below for the ERGO LE32CT5000AK LED TV repairing.

ERGO LE32CT5000AK LED TV Software download free.

How to Download Free Software for ERGO LE32CT5000AK LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/07/2023
0 51

ERGO LE39VT6 LED TV FLASH DUMP
Download Here

ERGO LE39VT6 LED TV

ERGO LE39VT6 LED TV Software file is shared for repairing purpose. If the ERGO LE39VT6 LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ERGO LE39VT6 LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ERGO LE39VT6 LED TV is still dead then check the primary power circuit if found ok then test the sERGOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sERGOdary voltage of the main board of the ERGO LE39VT6 LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ERGO LE39VT6 LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ERGO LE39VT6 LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ERGO LE39VT6 LED TV:
- Make/Brand: ERGO
- Main Board/Chassis: CV9202H-T
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ERGO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ERGO LE39VT6 LED TV dump file is shared below for repairing the firmware problem. ERGO LE39VT6 LED TV has the main board CV9202H-T installed in it so the SPI Flash file backup saved from working board CV9202H-T. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. CV9202H-T dump file is shared below for the ERGO LE39VT6 LED TV repairing.

ERGO LE39VT6 LED TV Software download free.

How to Download Free Software for ERGO LE39VT6 LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done
18/07/2023
0 131

ERGO LE28CT5000AK LED TV FLASH DUMP
Download Here

ERGO LE28CT5000AK LED TV

ERGO LE28CT5000AK LED TV Software file is shared for repairing purpose. If the ERGO LE28CT5000AK LED TV does not turn on mean not leaving the standby position or the remote control is not responding and even the control buttons/keys on LED TV not working then Software file can be loaded.

Troubleshooting Guide:

If the ERGO LE28CT5000AK LED TV is dead. Mean no power no flash light or indicator then first check the physical damage/burnt area, short circuit then power supply. In start check the fuse of main input if available then also check the power cable/wire continuity because in case of short circuit mostly the fuse burnt and cut off the supply.

If both are found ok and ERGO LE28CT5000AK LED TV is still dead then check the primary power circuit if found ok then test the sERGOdary power circuit. In this case if fault diagnose in power supply and can be repaired then no need to load Software file the TV will be normal after repairing and if the standby light is indicating and the TV not leaving standby or not responding remote and also all the primary and sERGOdary voltage of the main board of the ERGO LE28CT5000AK LED TV are tested and found accurate then write Software file, hope the issue will be resolved by rewriting flash memory.

Installation Instructions:

For writing Software file in ERGO LE28CT5000AK LED TV board, first of all save the backup of old dump then erase the flash chip. After it write the given ERGO LE28CT5000AK LED TV Software and then verify after completion. if verifies successfully then resold it again and check. In some cases the Software file is saved from the same board but the remote control may not match. In such cases use universal remote control.

Technical Specifications ERGO LE28CT5000AK LED TV:
- Make/Brand: ERGO
- Main Board/Chassis: TP.MS3463S.PB801
- Board Type:
- Power Source:
- Rated Power Consumption:
- Panel Info:
- T-CON:
- Screen Resolution:
- Main Processor/Chipset:
- SPI Flash:
- Tuner:
- Firmware Type: SPI Dump
- Product User: ERGO
- Product Model:
- Factory Code:
Special Note:

The attached firmware is backup dump file and can be loaded by a programming tool in case when LED TV stuck on Logo or Boot Screen or not leave the standby position. Not for Update purpose if LED TV is working Normal. Always match Main board number before writing the Software File. If you are not a technician or do not have any experience of repairing electronic devices then do not play with this. In case of wrong file loaded, board may be dead. Admin Team is not responsible in case of any damage/loss.

Click for more Softwares TV

About Mainboard:

ERGO LE28CT5000AK LED TV dump file is shared below for repairing the firmware problem. ERGO LE28CT5000AK LED TV has the main board TP.MS3463S.PB801 installed in it so the SPI Flash file backup saved from working board TP.MS3463S.PB801. Mostly in LED TVs universal board is installed which has the integration of backlight driver board, ATV Tuner Module and Power Circuit board. TP.MS3463S.PB801 dump file is shared below for the ERGO LE28CT5000AK LED TV repairing.

ERGO LE28CT5000AK LED TV Software download free.

How to Download Free Software for ERGO LE28CT5000AK LED TV:

1. Click on the file part or Download Link, New Tab will open
2. Click on Free Download or Premium Download as per your account type
3. Check I’m not robot and wait for countdown timer to end
4. Click on Create Download Link
5. Ignore Popups and wait for Preparing Download Link
6. Click on Click Here To Download. Done. Click on Click Here To Download. Done